what are you looking for?
EEC-FT wire inspection ECT is designed with 5 independent testing channels which can test 5 lines at the same time. The start and end of each channel can be controlled individually. The optional powerful report system makes the testing data analysis easily. It is widely used for tungsten wire inspection and molybdenum wire inpsection.
EEC-FT is designed with 5 independent testing channels and wide frequency range from 64Hz to 5MHz. It enables to connect at most 5 coils, and the testing signal and the parameters of the 5 channels can be showed on the same screen at the same time. The start and end of each channel can be controlled individually. The optional powerful report system makes the testing data analysis easily.
EEC-FT can be used in nuclear energy, electric power, petrochemical, auto parts, and viation etc.. It is well used for defect testing and thickness measuring of tubes, rods and wires; for metal component inspection such as welded steel strip, pumping rod, valve lever, gear, hub, hollow shaft and bolt etc. The report system makes it very popular for tungsten wire and molybdenum wire inpsection.
Advanced Features
• Five independent channels for 5 coils at most at the same time, and the start and end of each channel can be controlled individually
• Parameter is adjustable with computer in full-digital way, data and graphics can be saved and called out for analysis
• Parameters can be stored in advance and easily called out for same application inspection when needed
• Impedance plane and time-base strip chart can be showed for all the 5 channels at the same time
• Output of sound and light alarm, real-time and delayed marking, sorting signal are all available
• High resolution for microcrack
• Fast digital electronic balance
• Automatically calculate and show the the defect phase and amplitude
• Optional for powerful report system, report for each channel can be saved individually
• Languages available in English and Chinese
|
Specifications |
|
|
Channel |
5 independent channels |
|
Channel Control |
The start and end of each channel can be controlled individually |
|
Frequency |
5 frequencies with each channel one frequency |
|
Frequency Range |
64 Hz-5 MHz |
|
Max Testing Speed |
150M/min |
|
Gain |
0-90 dB in 0.5 dB steps |
|
Phase |
0-360° in 1° steps |
|
Gain Ratio (Y/X) |
0.1-10 |
|
Display Mode |
Various display mode |
|
High Pass Filter |
0-500 Hz |
|
Low Pass Filter |
10-10000 Hz |
|
Digital Filter |
1-100 |
|
Start/End Delayed Time |
0-32S |
|
Delayed Marking Time |
0-200S |
|
Marking Duration |
1-32S |
|
Clock Mode |
Inner clock for timing, Outer clock for encoder |
|
Alarm Output |
5 alarm output |
|
Input Signal |
NC and NO for A-scan and encoder |
|
Printer Can Be Connected |
Laser printer of EPSON/HP |
|
Operating Temperature |
0°C to 40°C |
|
Storage Temperature |
-20°C to 50°C |
|
Power Supply |
AC 220V/110V |
Widely Used For
• Crack detection for aircraft components, axles, machine parts, bolts and so on
• Surface inspection for welds with or without coating
• Online/offline inspection of tubes, rods, wires
• Sort different heat treatment conditions and different materials
EEC-309 is designed with MIMO and OFDM technology, which greatly improves the testing speed of RFT. It is widely applied for high speed tube inspection, heat exchangers inspection, condensers inspection etc. It also enables to inspect defects and check wall thickness at the same time.
Learn More
EEC-FT wire inspection ECT is designed with 5 independent testing channels which can test 5 lines at the same time. The start and end of each channel can be controlled individually. The optional powerful report system makes the testing data analysis easily. It is widely used for tungsten wire inspection and molybdenum wire inpsection.
Learn More
EEC-22D Eddy Current Sorting System is specially used for material sorting, hardness sorting, heat treatment sorting, and flaw inspection of metal tubes, bars, wires, auto parts, valves and various metal components. The difference of structure, case depth can be well separated too.
Learn More
EEC-23 eddy current tester can be used for the on-line/off-line tube inspection, bar inspection, wire testing and so on. Work with different probes and accessories, this machine can realize different functions. For example, with saturation device, it can be used for the inspection of ferromagnetic materials; with special probes of welding, it can be used to test welding quality on line or by hand.
Learn More
Heat exchanger tube inspecton system with ECT and RFT functions for both ferrous and non-ferrous tubes. Mixing function enables noise signal remove from the support plate, and tube sheet mapping enables to draw the tube layout and to mark the testing result with different colors.
Learn More
EEC-F ECT sorting system is provided for hardness sorting, material sorting, and heat treatment sorting. It can be used for inspection and sorting of metal tubes, bars, wires, auto parts, valves and various metal components. The difference of structure, surface hardness, case depth can be well separated too.
Learn More
This new powerful eddy current flaw detector makes the manual inspection much easier, faster and more accurate. Defect inspection, weld inspection, conductivity measurement and coating thickness measurement are all included in this instrument. The all-in-one design makes the small body with strong function.
Learn More
With 4-channel and 2-frequency design, this eddy current crack detection instrument enables high-sensitivity and high-efficiency manual inspection. Inspection settings for different applications can be stored in files and simply called up when needed.
Learn MoreWants To Get Latest Updates! Sign Up For Free.
